XP spjällaxel till SAAB 92A
Hög flödes spjällaxel till Solex 32 AIC
Ökar flödet kraftigt ock kan göra någon hp på en standard SAAB 92
Kan även passa även andre tidiga bilar som Bristol samt Mercedes
Best nr: F5 för SAAB 92 pris 500:- |
|
 |
XP-throttle shaft for Solex 44 PII
To increase the carburetor flow area with 17 % a specially designed
extra thin shaft has been developed. The shaft is only 2 mm thick and is
made in stainless steel to take the strain and equipped with two O-ring
seals.
Delivered with special low profile brass bolts for maximum flow.
Order no: F8 Price 1250:-
|
| Läs mer om XP-spjällaxel |
 |
|
 |
XP-Venturi
New made venturis suitable for Solex 40AI, 40BI and 40DHW.
Designed according to theoretical guidelines and flow tested in an Superflow SF60 test bench together with the carburetor and intake manifold to get the maximum flow and the best carburetor function. Available dimensions are 31, 32, 33, 34, 35, 36 mm where 31-34 mm mainly is recommended for the single carb engine and 35-36 mm for the Sonett II.
Order no: F1 Price: 280:- |
|
Zoom
image |
| |
Solex
original main jets
Original
jets in sizes as close as 2,5.
Available in most sizes from 125 to 280 as long as the batch
we found will last!
Thus 125 , 127.5 , 130 , 132,5 and beyond.
Order no : F2 Price: 60:- /each |
|
Zoom
image |
| |
|
Solex
original emulsion jets
Original jets. Available in almost all common sizes.
Order no: F3 Price: 60:- /each |
|
Zoom
image |
| |
|
Solex
original idle jets
Original jets. Available in almost all common sizes.
Order no: F4 Price: 80:- /each |
|
Zoom
image |
| |
|
XP-throttle
shaft for the single carburetor Solex 40 AI or BI
To increase the airflow trough the single carburetor 93-96 engines,
we have developed an extra thin stainless steel throttle shaft
with o-rings seals.The shaft is sold complete with special made
extremely low profile screws for maximum flow. It is also prepared
to take throttle plates up to 44 mm.
Order nr: F5 Price 650:-/st
Read more |
|
Zoom
image |
| |
|
XP-
throttle shaft for 66- and MC850 Engines
To
increase the carburetor flow about 8% a specially designed extra
thin shaft has been developed. The shaft is only 2mm thick and
is made in stainless steel to take the strain and equipped with
an O-ring seal. Delivered with special low profile brass bolts
for maximum flow. Also suitable for throttle houses taken up
to 36 mm.
Order no: F6 Price 1250:-
Read
more
|
|
Zoom
image |
| |
|
XP
throttle house & XP throttle house kit for Solex 40
To increase the flow of the carburetor about 6% the throttle
house is taken out to 44mm and brass bushings is inserted to
minimize any shaft leakage. The throttle house is also sold
as a complete unit together with the XP-throttle shaft. The
renovation and overbore throttle houses are sold on an exchange
basis.
Order no: F9 XP 44mm throttle house: Price:
1250:-
Order no: F10 Complete 44mm throttle house kit : Price
1750:-
| Read
more |
|
Diagram
|
|
|
|
Zoom
image |
| |
|
XP
36mm throttle house & XP throttle house kit
To increase the flow of the triple carburetor the throttle house
is taken out to 36 mm and brass bushings is inserted in the
front end to minimize any shaft leakage. Also new 1 mm thin
plates are made to give maximum flow.The throttle house is also
sold as a complete unit together with the XP-throttle shaft.
The renovation and overbore throttle houses are sold on an exchange
basis.
Order no: F11 XP 36mm throttle house:
Price: 1450:-
Order no: F12 Complete XP 36mm throttle house kit: Price:
2650:-
| Read
more |
|
Diagram
|
|
|
|
Zoom
image |
| |
|
XP-Reed
valves for Sports and triple carb engines
Contains
a complete reed kit to be mounted in between the engine block
and the intake manifold and gives the engine a remarkable strong
bottom end.This reed adaptor also allows the intake side to
be opened up a lot to give a further increase in top end power.
Has been tested on the rolling road dyno on an 866cc SAAB engine
producing 93 hp at 6400 rpm.
Order no: F7 Price complete: 4 500:- |
|
Zoom
image |
| |
|
Engine